6600 cemplan

Self-levelling compound
EN 13813 CT-C30-F6
Fine grain levelling compound for an especially smooth levelling layer
Rapidly hardening
Polymer reinforced
Good adhesion
Wear resistant
Suitable for use under rugs and membrane

Detailed description


6600 cemplan is recommended for levelling concrete, screed, and ceramic tiles.

6600 cemplan is a dry product that is ready to use after mixing with water.

6600 cemplan is self-levelling and easy to smoothen.

6600 cemplan is available in 15 kg paper bags.


Product description

Cement based, polymer reinforced, floor levelling compound.


Application areas

For plain levelling in wet as well as dry areas. 6600 cemplan can be applied with hand tools or mixing pump.


Type of substrate

6600 cemplan can be applied on substrate of concrete, screed and lightweight concrete.


Pre-treatment of substrate

The substrate must be dry, coherent and cleaned of dust, grease and dirt. Any cured laitance and weak parts of the substrate must be cleared and repaired. Loose dust to be removed with vacuum cleaner. Use mira 7110 base cleaner to clean the substrate using high pressure water or other effective method.



Absorbent substrates is primed with 1 part of 4180 primer diluted in 3 parts of water. The primer is worked well into the substrate with a brush. When more layers are applied, each layer should be primed before applying the next.



15 kg powder to be mixed with 3,6 - 3,7 litres of clean water. For the best result, mix a minimum of 2 minutes with a cement mixer or pump, until the mixture is homogenous.

The flowability can be tested using the flow test. Place the test tube on a level surface, fill the tube to the top edge with mixed 6600 cemplan, lift the tube so the compound can flow freely. When the compound has flowed completely by its own, the diameter is measured (see technical data).

The floor levelling compound can be applied in approx. 20-30 minutes after mixing at room temperature 10-20°C. The compound should be poured out onto the floor immediately after mixing. 6600 cemplan levels out by itself, but can be smoothened and spread into corners by using the smooth side of a trowel.

Depending on room temperature and air moisture the layer is ready for light foot traffic after 1,5-2 hours. Further treatment can begin after 24 hours. In wet rooms, use mira 4400 multicoat waterproofing on top of the floor screed.


Working environment

The product contains cement. Working hygienic rules for cement must be followed.

6600 cemplan is guaranteed chrome neutralized in minimum 12 months.

Reference to product safety data sheet.


Storage and transportation

Transport and store dry. 6600 cemplan keeps technical specification minimum 6 months after production date in unopened packaging. Can be used hereafter, technical properties may however, change; for example, the setting time may be extended.


Areas of Application

Indoor Areas
Indoor Floor
Dry room
Levelling compound
Old ceramic tile
Suitable Cover Material
Ceramic Tile
Natural stone
Floor paint
Soft cover material


Average: 1,6 kg /m² /mm
Layer Thickness
0,5-10 mm
Working Time and Temperature

Working temperature:


Working Time:

Light load: 1,5-2 h
Further treatment: 24 h
Waterproofing application: 12-18 h
Compression strength: 30 N / mm²
Flexural strength: 6 N / mm²

Dimensions and packaging

15 kg bag


6600 cemplan DS
Technical Data Sheet
6600 cemplan DoP
Declaration of Performance
6600 cemplan EC1
EC1 Licence
EPD mira self leveling compound and concretes
Environmental Product Declaration
6600 cemplan M1
M1 Emission Classification
M1 Emission Classification
6600 cemplan SDS
Safety Data Sheet

Related products

Mira 4140 contact primer 10kg (front)
4140 contact primer
A two component contact primer for creating an adhesive layer on non-absorbent substrates before the application of a self levelling compound, repair mortar, waterproofing, tile adhesive or other similar product.
Mira sponge grey
grey sponge
A special washing sponge for removing mira 3650 multipox epoxy grout haze
Mira planstop
Rubberfoam strip. For limiting self-levelling floor compounds from flowing at doorsteps, gullies etc.
Mira level pin
level pin
Ensures right thickness for levelling compounds
mira 7110 base cleaner 1l (front)
Alkaline cleaning agent
7110 base cleaner
A high quality prewash solution for tiles before further treatment. Removes oil, fat and dirt from ceramic tiles and natural stone. Suitable for the cleaning of all surfaces before further treatment or covering.
Mira 4180 primer (front)-01
4180 primer
A primer for porous substrates before the application of a levelling compound, hydroisolation, tile adhesive etc
mira sponge
soft sponge

Packaging Details

ImageProductEANCodeX (mm)Y (mm)Z (mm)Neto Weight (kg)Bruto Weight (kg)Best Before (Days)
mira 6600 cemplan, 15 kg570191466006350660035002401201515.11180