Self-levelling compound
EN 13813 CT-C30-F6
Self-levelling compound for creating both sloped and level layers on all types of substrates
Polymer reinforced
Fiber reinforced
Good adhesion
Wear resistant
Suitable for heated surfaces
For levelling wooden and concrete substrates

Detailed description


x–plan is recommended for levelling of most floor types f. ex. concrete, floor screed, light concrete, gypsum substrate, wooden floor, ceramic tiles etc.

x–plan is a dry product, which can be used after mixing with water. x–plan is partly self-levelling and easy to smoothen.

x–plan is available in 25 kg bags.


Product description

Cement based, polymer and fibre reinforced floor levelling compound. Dust reduced.


Application areas

For levelling and building of slopes in wet and dry rooms. x–plan is suitable for all types of water and electric based heated floors.

x–plan can be applied with hand tools or via a mixing pump.


Type of substrate

x–plan can be applied on substrates of concrete, screed, light concrete, gypsum, chipboard, plywood or wooden floors with movements and deformation risk.

On concrete, screed, painted concrete surfaces and ceramic tiles, the layer thickness is 2 – 50mm.

On lightweight concrete the layer thickness is 5 – 30mm and on wooden floor 5 – 50mm. On wooden floor reinforcement mesh/ uninet shall be cast in when floors are to be covered with clinker tiles, tiles, or natural stones.


Pre-treatment of substrate

The substrate shall be load carrying, stable, coherent, clean, free of dust, grease and cement laitance.

Any concrete laitance and weak parts of concrete substrates shall be removed. Dust shall be removed with vacuum cleaner. Grease, oil etc to be removed with 7110 base cleaner, high pressure water cleaning or other effective cleaning method.



Absorbent substrates shall be primed with 1 part 4180 primer diluted with 3 parts of water.

The primer shall be worked properly into the substrate with a brush. Non-absorbent substrates as ceramic tiles or painted surfaces is primed with 4140 contact primer. Wooden substrate shall be primed with concentrated 4180 primer. If more than one layer of x–plan is applied, priming is needed between the layers.



25 kg powder to be mixed with approx. 3,8-4,5 l of clean water. For building a fall, the water content should be reduced to approx. 3.2 l per 25 kg x–plan. Use a mixing paddle on drill or mixing pump. Mix minimum 2-5 minutes to homogeneous mix.

Flowability can be controlled with flow test. Place test tube on a flat surface, fill it to top edge with mixed x–plan, lift the tube so the mixture can flow freely. When x-plan by itself has spread out, measure the diameter. See technical data.

The mixture can be used in approx. 15 – 20 minutes after mixing at room temperature of 10 - 18oC.

Pour the compound onto the floor immediately after mixing. x–plan planes out by itself, but it is recommendable to use the smooth side of a trowel to smoothen and spread it into corners.

For thin heating floors with cables on combustible substrate reinforcement mesh/uninet is recommended. The heating cables shall be covered with minimum 5 – 10mm x-plan dependent on effect of cables and stability of substrate.

For building a slope, x–plan is applied along the wall and will run by itself towards the gully. Cover around the gully with self adhesive planstop foam rubber. Once hardened so much that you can walk on it the slope can be finished and adjusted to match the floor drain.

Dependent on room temperature and air humidity the screed is ready for light foot traffic after approx. 2 hours. Ceramic tiles can be installed after 6 – 12 hours. In wet rooms waterproofing of surface with 4400 multicoat can take place after 12 – 18 hours at the earliest.


Working environment

The product contains cement. Working hygienic rules for cement must be followed. x–plan is guaranteed chrome neutralized for at least 12 months.

Reference the product safety data sheet.


Storage and transportation

Transport and store dry. x-plan keeps technical specifications for at least 6 months after the production date in unopened packaging. Can be used after that, however, the technical properties may change. For example, the setting time may be extended.


Areas of Application

Indoor Areas
Indoor Floor
Wet Room
Dry room
Lightweight concrete
Levelling compound
Heated floor
Ceramic tile
Floor plank
Floor beams
Suitable Cover Material
Ceramic Tile
Natural stone
Floor paint


For level layers
3,8-4,5 l  Water  + 25 kg  Powder
For building slopes
3,8 l  Water  + 25 kg  Powder


Average: 1,7 kg /m² /mm
Layer Thickness
2-50 mm
Working Time and Temperature

Working temperature:


Working Time:

Light load: 2-3 h
Further treatment: 6 h
Waterproofing application: 12-18 h
Compression strength: 30 N / mm²
Flexural strength: 6 N / mm²

Dimensions and packaging

25 kg bag


x-plan DoP
Declaration of Performance
x-plan EC1
EC1 Licence
EPD mira self leveling compound and concretes
Environmental Product Declaration
x-plan M1
M1 Emission Classification
M1 Emission Classification
x-plan SDS
Safety Data Sheet

Related products

Mira 4140 contact primer 10kg (front)
4140 contact primer
A two component contact primer for creating an adhesive layer on non-absorbent substrates before the application of a self levelling compound, repair mortar, waterproofing, tile adhesive or other similar product.
Mira uninet-01
Reinforcement net
For reinforcing the levelling compound and installing heating cables
Mira planstop
Rubberfoam strip. For limiting self-levelling floor compounds from flowing at doorsteps, gullies etc.
Mira flexband
L-shaped cellfoam band for deformation joints. Prevents the self-levelling compounds from flowing under wall, forms a deformation joint between the wall and the floor screed.
Mira level pin
level pin
Ensures right thickness for levelling compounds
mira 7110 base cleaner 1l (front)
Alkaline cleaning agent
7110 base cleaner
A high quality prewash solution for tiles before further treatment. Removes oil, fat and dirt from ceramic tiles and natural stone. Suitable for the cleaning of all surfaces before further treatment or covering.
Mira 4180 primer (front)-01
4180 primer
A primer for porous substrates before the application of a levelling compound, hydroisolation, tile adhesive etc
Mira EPS lightbeton 360 50L (+d22)
Special mortar
EPS lightbeton 360
EPS granule based lightweight floor screed for building a lightweight and stiff subfloor.
MIra 4400 multicoat 15 kg (front)-01
Waterproofing paste
4400 multicoat
Highly flexible water vapour and waterproofing paste with good crack bridging abilities for use in wet rooms like bathrooms and washrooms

Packaging Details

ImageProductEANCodeX (mm)Y (mm)Z (mm)Neto Weight (kg)Bruto Weight (kg)Best Before (Days)
mira x-plan, 25 kg57019146702085060000EE4502601002525.11180