3110 unifix

Tile adhesive
White non-flowing tile adhesive with good adhesion and improved flexibility. Suitable for heated floors, natural stone, glass mosaic, ceramics etc
High flexibility (S1)
White cement based
Polymer reinforced
Very good adhesion
Non-flowing – the tile will not slip
Suitable for natural stone and glass mosaic
Long adjustment time

Detailed description


3110 unifix is expecially suitable for installing absorbent tiles on stable substrates with minimal risk of deformation.

3110 unifix is a dry mixture that after mixing with water is ready to use. The tile glue is easy to prepare and apply.

3110 unifix is supplied in 5 kg and 25 kg bags.


Product description

Cement based, frostproof, water resistant and polymer strengthened white tile adhesive in low dust powder form.


Application areas

For mounting ceramic tiles, clinker and natural stone, inside and outside, in wet and dry areas. Suitable for heated floor and thin translucent tiles, glass mosaic, light marble and other similar tiles.


Types of substrate

Stable floors and walls with moderate tension/deformation as rendered/plastered bricks, block walls, gypsum plates, concrete elements and light concrete elements with moderate shrinkage, movements and deformation.


Pre-treatment of substrate

Ensure substrate has carrying capacity, is stable and coherent, cleaned for dust, grease and cement laitance. The substrate must be so dry that 4180 primer can be absorbed in the surface.

Absorbent substrates shall be primed with 4180 primer and in wet rooms water tightened according to rules laid down in mira`s installation instructions for wet rooms.



Mix 25 kg powder with 6,25 - 7 l clean water to a lump free mortar and the mix is ready for use. For mixing it is recommendable to use a mixing paddle. The powder, water and substrate shall be within the recommended working temperature.

The adhesive can be applied within approx. 6 hours after mixing. Ensure tiles are fixed quickly to avoid formation of skin on adhesive surface.

3110 unifix shall be spread on the substrate with a notched trowel. First spread the adhesive with the smooth side and then draw the notched side through the mortar. Follow the recommendation for correct choice of tooth size for tile type and substrate.

The tiles are pressed/twisted in place in the wet adhesive. Ensure frequently that the backside of the tile is fully covered.

Areas above 36m² and areas of a length above 8 m shall normally be divided in areas with expansion joints across the construction.

Dependent on absorbing capacity of tiles and room temperature tiling is ready to be grouted after approx. 10 hours for walls and 18 hours for floors.


Working environment

The product contains cement. Working environment rules for cement must be followed.

3110 unifix is based on white cement containing a natural low content of chrome(VI) therefore the limiting value of max. 2mg/kg is always kept.

Reference the product safety data sheet.


Storage and transportation

Transport and store dry. Product will maintain technical specifications minimum 12 months from production date in unopened packing. Can be used hereafter technical properties may, however, change; e.g. setting time may be extended.



C Cement-based
2 Adhesion at least 1.0 N / mm²
T Thixotropic (Non-flowing)
E Extended open time
S1 Flexible

Areas of Application

Indoor Areas
Indoor Floor
Indoor Wall
Wet Room
Dry room
Outdoor Areas
Outdoor Floor
Outdoor Wall
Medium deformation
Lightweight concrete
Levelling compound
Heated floor
Lightweight concrete block
Gypsum board
Plastered masonry
Old ceramic tile
Gypsum plaster
Wet room waterproofing
High deformation
Wooden board
Tile Size
Normal sized tiles
Tile Type
Natural Stone
All tile types
Glass mosaic


Walls (average): 2 kg /m²
Floor (average): 3,5 kg /m²
Working Time and Temperature

Working temperature:


Working Time:

Further treatment: 10-14 h
Full strength: 7 days

Dimensions and packaging

5 kg bag
25 kg bag


Secure tile fixing
The correct choice of tile adhesive


3110 unifix DS
Technical Data Sheet
3110 unifix DoP
Declaration of Performance
3110 unifix EC1
EC1 Licence
EPD mira tileadhesive
Environmental Product Declaration
M1 Emission Classification
M1 Emission Classification
3110 unifix SDS
Safety Data Sheet
ETA 090156
ETA Certificate
ETA 120008
ETA Certificate
ETA 150868
ETA Certificate
Tile adhesives with CE certificate
Efflorescence manual


mira 3110 unifix 5kg (+45)
mira 3110 unifix 5kg (+22)
mira 3110 unifix 5kg (front)
mira 3110 unifix 5kg (-22)
mira 3110 unifix 5kg (-45)

Related products

Mira 4140 contact primer 10kg (front)
4140 contact primer
A two component contact primer for creating an adhesive layer on non-absorbent substrates before the application of a self levelling compound, repair mortar, waterproofing, tile adhesive or other similar product.
Mira supercolour 15kg (front)
A cement based polymer reinforced grout filler for walls and floors both indoors and outdoors in dry and wet rooms
Mira 4180 primer (front)-01
4180 primer
A primer for porous substrates before the application of a levelling compound, hydroisolation, tile adhesive etc
MIra 4400 multicoat 15 kg (front)-01
Waterproofing paste
4400 multicoat
Highly flexible water vapour and waterproofing paste with good crack bridging abilities for use in wet rooms like bathrooms and washrooms

Packaging Details

ImageProductEANCodeX (mm)Y (mm)Z (mm)Neto Weight (kg)Bruto Weight (kg)Best Before (Days)
mira 3110 unifix (C2TE S1), 25 kg570191431106450311074502601002525.11365
mira 3110 unifix (C2TE S1), 5 kg5701914311026503110523015010055.055365