Secure tile fixing

The correct choice of tile adhesive

mira tile adhesive for all types of jobs

The key to good tile work lies in the quality of the tile adhesive, as properties such as adhesion strength and flexibility are crucial for ensuring that the tiled surface achieves the necessary strength and long lifetime.


In addition, it is important to look at the adhesive’s working and open time, strength, and setting time. This is why all mira tile adhesives are labelled with a CE classification detailing the product’s characteristics.


For example, if you’re not completely sure of the conditions, it can be a good idea to use an S2 classified tile adhesive, which has over twice the flexibility of an S1 classified adhesive.

CE classification – how to read it

In order for a tile adhesive to be CE-certified, it must at minimum fulfil the adhesive requirements which are described below. These requirements are tested in water, under heat conditions of +70°C and alternating freeze/thaw cycles.





Setting time




Working/Open time




C Material

The letter C classifies the adhesive as a cement-based product.

T Firmness

The declaration’s letter T (thixotropic) means that the tile on a horizontal surface may slide a maximum of 0.5 mm. If unclassified, the tile may slide a max. 2 mm.

2 Strength

In addition to the C marking, a declaration for tile adhesive MUST show an adhesion strength class 1 or 2, where 2 is the highest.

Class C1 = > 0,5 N/mm²

Class C2 = > 1,0 N/mm² after full hardening.

E Working/open time

The declaration’s letter E (extra-long open time) means that the tile can be mounted/adjusted up until 30 minutes after affixing the tile to the surface. If unclassified, the standard is 20 minutes.

F Setting time

The declaration’s letter F (fast) means that the tile adhesive sets quickly and has achieved a minimum adhesive strength of 0,5 MPa after six hours setting time.

S2 Flexibility

Only tile adhesive that has been declared as C1 or C2 can fulfil the requirements for S1 and S2 testing. In order to be classified as S1, the tile adhesive must have a flexibility of 2.5 mm. For S2, the requirement is 5 mm.

CE classification – what you should consider

Strength C2 is often seen as better than C1. This can be very misleading, as the strength only shows its ability to stay put. E.g., a 20×20 cm ceramic tile requires a tensile strength of approx. four tonnes for C2 and two tonnes for C1 to pull the tile off the surface. C1 tensile strength is usually sufficient in all indoor settings (apart from very challenging industrial environments). More interesting are S1 and S2 , which indicate the elastic deformation capability of the adhesive. Tile adhesives that are not classified as S1 or S2 are legal to use but have no defined elasticity and can be as hard as cement.


Today’s ceramic tiles are generally sealed and have virtually no absorbency, and they often have a white release agent on the tile surface to prevent the tile from fusing to the mould during production. Unfortunately, this release agent makes it harder for the adhesive to bind. This is why you should take care to choose adhesives with maximum bonding strength to avoid poor adhesion. Adhesives with S2 have the greatest flexibility and thus also the maximum adhesion.

Other classifications


Products labelled with M1 live up to strict requirements for VOC emissions laid down by the Building Information Foundation RTS in Finland. This guarantees that the products contribute towards a healthy indoor climate with extremely low emissions of harmful substances and minimal nuisance odour.


Products labelled with EmiCode live up to strict requirements for VOC emissions laid down by the German organisation for consumer protection, GEV. This guarantees that the products contribute towards a healthy indoor climate with extremely low emissions of harmful substances.


Our ”Low Dust” products for cast-filling, grouting and tile adhesives are developed to generate less dust while working, a lighter cleaning of tools, and easier mixing and application – in brief, a better working environment for you and your colleagues.

Product overview​

3100 unifix


Grey, cement-based, frost resistant, waterproof, polymer-reinforced with very good adhesion, dry mixture for stable floors and walls with minimal risk of deformation. For all types of ceramic tiles. We recommend using it mostly indoor on stable substrates like non heated floors, on concrete, stone and gypsum boards walls.


As mira 3100 unifix is grey, it is not recommended for thin tiles, glass mosaic, light marble etc because the tone of the adhesive can be visible. Recommended to use up to 30x30cm tiles.

25 kg sack

3110 unifix


White cement-based, polymer-reinforced adhesive that can be used for most types of tiles and natural stones on surfaces with moderate risk of movement and residual waste.


Suitable for heated floors, surfaces of rendered brickwork, filler, plaster and silicate boards, lightweight concrete and concrete substrates, wet-room membranes. Recommended for tile work in residential and office buildings as well as light industry etc.. We recommend to use for tiles in sizes up to 60 x 60 cm.

5kg / 15 kg sack

mira tile adhesives

The working conditions on construction sites and the areas of application of our products are highly diverse. We can only give general instructions for the use of our products. Following recommendations are in accordance with the information currently available to us and.


If there is several products available from our range for the application we recommend to use product what is more suitable for that application. Therefore recommendations about tile sizes in real life may vary up and down depending on conditions, tile quality and applicant skills.


Architects, engineers and the users of our products are under an obligation to verify the suitability of our products and the feasibility of using them for their specific applications.

3130 superfix


White adhesive with maximum adhesion and highest flexibility classification. Suitable for substrates with a heightened risk of deformation like fireplaces, heated floors, etc. Can be used for all types of indoor surfaces just like 3110 unifix and outdoors on terraces and balconies, as well as for industrial applications, pools etc.


Suitable for mounting of sealed non-absorbent tiles. Can be used on all types of mira membranes, epoxy surfaces and old tiles etc. For all tile sizes ( also large format). When using with large-format tiles on floors (60 x 60 cm), 3250 gigafix floor is recommended.

5kg / 15 kg sack

z-fix excellent


White, lightweight tile adhesive with maximum flexibility. Can be used for most types of tiles, natural stone etc. in residential areas, office spaces, and light industrial indoor settings. Particularly well-suited to large-format tiles on walls and floors in residential areas and similar, as it is easy to mix during application and installation.


Covers 30% more area than traditional tile adhesives. It is recommended that tiles with a release agent on the adhesive side are given a thinly scraped coating of adhesive before mounting. For large-format tiles on floor surfaces (60 x 60 cm) we recommend 3250 gigafix floor.

10 kg sack

3250 gigafix floor

C2E S2

White self-compacting adhesive for mounting large-format tiles on the floor (not recommended for tile formats smaller than 20 x 20 cm). The tile adhesive is pressed in and distributed over the entire tile surface with short vibrating motions. Large-format tiles with release agent on the back should have a thinly scraped coating of adhesive before mounting.


When working with levelling sticks, 3250 gigafix floor ensures that the tile adhesive follows the tile upon level adjustment.

5kg / 15 kg sack

3100 unifix
3110 unifix
3130 superfix
3230 superrapidfix
3250 gigafix floor
light fix
z-fix excellent
3600 multicrete
Working time (h)
~ 6
~ 6
~ 6
~ 0,5
~ 3
~ 1
~ 6
~ 6
~ 0,5
C2E S1
C2E S2
Coverage (kg / m²)
2 – 6
2 – 6
2 – 6
2 – 6
3 – 9
3 – 9
1 – 3
1 – 3
2 – 4
Substrate deformation
Hardening time
Further treatment (h)
10 – 24
10 – 24
10 – 24
2 – 4
18 – 24
6 – 12
10 – 18
10 – 18
3 – 6
Full load (days)
Apsildāmās grīdas
Floor screed
Apmests mūris
Ģipša plāksnes
Old tile / paint
Wooden surface
Stainless steel, plastic laminate
Building part
Sausās telpās
Wet room
Swimming pool
Tile size
Very large
Flīžu veidi
Every type
Keramiskās flīzes
Grès Porcelain tile
Dabīgais akmens
Stikla mozaīka

Tile installation


The greater the possible level of deformations of the substrate and the larger the tiles, the thicker the adhesive layer and the higher the flexibility class of the adhesive used for installation should be. Tiles are considered to be large, when one or more sides are longer than 30 cm and no side exceeds 120 cm.


The tolerance of the substrate must be a maximum of +/- 2 mm for every two metres. A tile adhesive can be used to compensate for this unevenness. Tiles that are larger than 120 cm in length require a more level substrate than smaller tiles. In that case the surface must be levelled with the fine-grained self-levelling compound mira 6600 cemplan, which can be applied in a layer of 10 to practically zero millimetres.


The higher the load that the surface must withstand, the more important it is that the tile adhesive covers as much of the back of the tile as possible.

Walls – On surfaces with a lighter load, it is necessary for the tile adhesive to cover at least 80% of the back of the tile. The tile adhesive must be properly rubbed onto the substrate and the tile pressed firmly into the adhesive.


Floors – On floors, the mixture should, as a rule, cover 100% of the back of the tile, in order to prevent the tiles from breaking. In living spaces with only a light load, the minimum coverage is 80%. In a heavy-duty environment, proper contact between the tile and the adhesive is especially important.


In outdoor conditions and on floors that must withstand heavy stress, 100% of the area of the back of the tile must always be covered with tile adhesive. In order to achieve good adhesion, it is sometimes necessary to apply the tile adhesive not only to the substrate but also to the back of the tile.

Lielas flīzes

When using larger tiles, a notched trowel is recommended to apply the adhesive to the tile. The dry layer (skin) that appears on the adhesive, reducing the adhesion, develops at a slower rate when the adhesive is applied with a notched trowel. It is also easier to press large plates into the adhesive in such a way that sufficient tile coverage is achieved.


To achieve the correct layer thickness, the notched trowel must be kept at the correct angle (70 – 80 º). The thicker the adhesive layer, the longer the drying time is as well.

Estimated coverage of tile adhesives

Longer side of tile
Trowel tooth size
Coverage (Heavy) 3100, 3110, 3130, 3230
Coverage (light) lightfix, z-fix
Coverage (self-levelling) 3250 Gigafix, Floorfix
Trowel with square teeth
10 cm
4 mm
1,5 kg / m²
1 kg / m²
15 cm
6 mm
2,1 kg / m²
1,5 kg / m²
25 cm
10 mm
3,2 kg / m²
2,4 kg / m²
30+ cm
12 mm
3,7 kg / m²
2,6 kg / m²
Trowel with round teeth
40 cm
10 × 20 mm
4,0 kg / m²
2,8 – 3,0 kg / m²
4,5 kg / m²
60 cm
12,5 × 20 mm
3,7 – 3,9 kg / m²
5,2 – 5,4 kg / m²
60+ cm
15 × 20 mm
4,5 – 4,8 kg / m²
6,5 – 7,0 kg / m²